10 Top Tips to Improve Your Boot Fitting Experience

10 Top Tips to Improve Your Boot Fitting Experience

Matt Cousins' Top 5 Gritstone Routes Reading 10 Top Tips to Improve Your Boot Fitting Experience 10 minutes Next Statement from SCARPA on the loss of Ueli Steck

This is a classic Scarpa Blog entry – some models, prices and specifications may have changed – see our website for the latest www.scarpa.co.uk

10 Top Tips to Improve Your Boot Fitting Experience

Scarpa pro skier Ross Hewitt talks through his top 10 tips to improve your ski boot fitting and help ensure you get a perfect fit for your skiing needs.

freedom-rs_prof

Chose the Right Type of Boot for the Job

Ideally I want a boot that offers race stiffness in the forward, lateral and aft directions, with a warm liner and enough space to stop my toes getting frostbite, has a walk mode, Vibram sole, and weighs less than 1 kg per boot. Unfortunately this doesn’t exist so think really hard and carefully what you want a boot for. If you are doing a lot of uphill or multi day tours then the Evo F1 could be ideal, but if it’s more downhill orientated you will appreciate the support of the Freedom. I run a World Cup race boot, a Freedom RS, and Evo F1 and the Alien to cover everything from 160 kph runs on my GS skis to skinning up hills for training. Spend a little time contemplating what you really want the boot to do and where you are willing to compromise.

Also bear in mind that a rockered Vibram sole is not compatible with traditional alpine downhill bindings and flat DIN soles should be used like those that come with the Scarpa Freedom. Some newer alpine bindings have a height adjustable anti-friction device at the toe that allows adjustment for the additional height between the rockered sole and the top of the toe piece.

Chose the Right Shell for Your Foot.

This may sound obvious but the boot that is most comfortable in the shop may just be the one that has most room around your foot and may end up being the sloppiest to ski. The choice of shell should not be based on colours, brand loyalty or magazine reviews. Each manufacture moulds it boots around its own last and they are all slightly different. The stock shell is just a starting point, and if it’s comfortable straight out the box then its probably too big or has too much volume for your foot. The correct shell length can be confirmed by removing the liner and placing your foot in the empty shell and with your toes just touching the front, there should be 1 cm between the heel and the shell. Remember that the liner will pack out through the moulding process and skiing, especially when the snow is heavy as you put more force through the boot to turn the ski. Once you have a shell that will provide a glove like fit, the boot fitter will heat the liners, put them back in the shell and then strap your feet into the liners while the moulding process goes on.

Customising the Shell for Your Foot

Once the liner has been moulded, the next step is to customise the shell for any tight or pinch points you may feel. It may be you need to ski the boot for a few hours to work out what needs modified or things may be apparent straight away in the shop. By removing the liner and applying some marker paint to any bone spurs, bunions, or bulges on your foot and then putting your foot back into the shell where the marker paint will be transferred to the inside of the shell. The boot fitter will decide if he can create more room in this area by grinding the internal surface of the shell or if the shell needs ‘blown’ out – a process involving softening the plastic of the shell with a heat gun and then applying and holding pressure to that area with a press. This is usually an overnight process as the plastic in the shell has a strong memory. I usually blow all my boots in the 6th metatarsal area and also at the heel due to bone spurs.

Don’t forget boots that fit well in the colder months may pinch your foot when it swells in the heat of the spring months requiring the shell to be pushed along the side. I find myself pushing my boots again in spring along the 6th metatarsal area since my feet get warm and swell up skiing north faces in mild temperatures between April and June.

Customising the Insole

Choose a footbed that will support your foot, closely fit the underside of your foot and provide good friction so foot movements result in instantaneous boot and ski movements. A good insole will also prevent the down force from tight buckles collapsing your foot and that burning lactate sensation which has you reaching to pop open the buckles at every opportunity. Raising the heel from footbed/insole/binding ramp angle (the angle off the horizontal due to the heal being higher than the toes) used to be common to try and make people more aggressive over the front of the skis. However it does the exact opposite. Try it at home, place a book under your heals and I bet you stick your bum out to compensate. In skiing this would make you more backseat. Now try this, feet flat on the floor, lift your toes and notice your weight going forward. Push your toes into the ground and you’ll feel your weight going backseat again. Try lifting your toes when skiing to get that weight forward.

Choosing the Liner

Surely the liner comes with the boot? Well it does but again you need to decide what you will do with the boot. If the intent is to do day tours you may have no specific requirements but if you are doing multi-day tours or expeditions then you will love Intuition closed cell foam liners. The closed cell structure does not absorb sweat so at the end of the day it’s easy to dry overnight in a hut or sleeping bag whereas a porous liner will stay saturated and may freeze without a direct heat source causing you major problems. There are other reasons why you may discard the stock liner. An Intuition Powerwrap is warmer, stiffer and will take some volume out of the boot, and the Intuition Pro Tour is designed specifically with that with a hinge point, rear stiffener and a choice of tongue stiffnesses.

Tips to Improve Your Boot Fitting

Scarpa’s boots come with Intuition Liners as stock

Customising the Liner

It’s now time to get the liner thermo moulded to your anatomy. The boot fitter will place the liner in an oven at 200 F for around 10 minutes until the liner loses a little stiffness. It will then be placed in the shell and you’ll be asked to slide your foot into the liner. The boot fitter may have already placed some foam pads on any bone protuberances to create more space for them while the liners conforms to your anatomy. If you are ski mountaineering, make sure you mould with toe caps in place to create a warm air space for your toes within the boot. Its essential that you get the heel firmly into the back of the boot and you’ll be asked to stomp down on the heel which will create a nice heel cup to hold your heel securely – you don’t want heel lift touring and any lateral heel movement will make it tough to smear the tail of the ski when you are buttering the turns off. The boot fitter will crank up the buckles and ask you to walk around and flex for ten minutes or so. And that’s it, well, almost. Final adjustments to remove volume can be done by adding customised shapes of self-adhesive foam to any problem areas. In the photo below you can see where I added 2 mm thick green foam around the heal to get the glove fit I was after with my skinny Achilles. These simple bits of foam can transform a boot from almost unskiable to world class so bear that in mind and if you think you’ll need some once the liner packs out ask the boot fitter to give you a sheet to take away. In the second photo below you’ll see how I put foam on top of my foot to take volume out around the ankle to get the heel locked down in the boot – super important with modern skis where you can use heal pressure to control the ski at the end of turns. Also if you have low volume foot like mine and your liner has a lacing option, use it.

Customising the fit of your liner with self adhesive foam & use of laces

Finally I am going to mention a few other things I use to get that glove like boot fit. Don’t forget boots that fit well in the colder months may pinch your foot when it swells in the heat of the spring months requiring the shell to be pushed along the side.

Spoilers – these typically come with alpine boots and are a wedge of plastic that Velcro’s to the top back of the liner to take out any space. Skiing is a very dynamic sport and when you want to put power on the back of the boot the last thing you want is a delay as your leg chances angle to move from shin contact to calf contact. My calf muscles also disappear as I go from the climbing and biking season into the ski season so it something I introduce as my anatomy changes through the season.

Volume Reducers

These are flat incompressible foam or rubber insoles that you place under your moulded insole to take out some volume. Typically 2 or 3 mm but if you need more a cork board might be the solution.

Heel lifts

An incompressible foam or rubber wedge under the heel to take out room. I don’t like these much as it changes the ramp angle – its remarkable that you will notice a change of a couple of mm in heel height causing you to be more backseat or thrown forward – until you get used to it and subconsciously compensate.

Heel Space Frame

These cheap plastic frames create a more pronounced heel pocket by inserting over the outside of the liner. They do push your foot forward and you’ll notice more pressure on your toes. I also find that while they are good for downhill, they tend to give me blisters along the sides of my Achilles and so I always use adhesive foam.

Tips to Improve Your Boot Fitting

You can view the full range of Scarpa boots here: http://www.scarpa.co.uk/ski/